Solars

Альтернативный источник питания

Солнечные панели предоставляют нам еще один способ для электрификации станции, они безопасны и если настроены правильно то могут обеспечить энергией всю станцию.

Местоположение

На станции всего четыре отсека с солнечными батареями. Ближайшая находится западнее инженерного отсека, вторая батарея находится чуть выше ассистентской восточнее шаттла прибытия, третья находится чуть выше церкви, западнее шаттла отбытия, четвертая батарея находится на юговостоке, недалеко от медбея и РнД.

Подключаем солнечные панели

Вам понадобится:

• много проводов.
• Так же space suit или rig suit.
• (Optional) crowbar открывать двери если небудет электричества.

Изначально ни одна из четырех солнечных батарей не подключена к станции. Вам нужно будет подключить солнечные батареи и солнечные трекера к проводам, идущим от станции.

Используйте провода и подключайте все не подключенные панели и трекер который служит для управления панелями.

Калибруем солнечные панели

Once you have wired an array, you need to calibrate the tracking and power so that it actually produces energy. The station is rotating in orbit, which means that the solar panels need to constantly rotate to face toward the sun. Click on the Solar Control CPU and set it to auto-tracking. You should see a degree displayed at the top ranging from 0 to 359; this is the current direction of the sun.

• 0 degrees = North
• 90 degrees = East
• 180 degrees = South
• 270 degrees = West

The consoles are a bit glitchy so you'll have to turn off auto-tracking then turn it on again before the panels start to rotate. Also, auto rotation is not smooth, it jumps about every 20 seconds. Keep this in mind if it seems like nothing is happening.

You don't need to use manual tracking. The only time you will ever need to manually calibrate a solar array is when something destroys the tracking unit.

It is important to note that THE STATION BLOCKS SUNLIGHT! This is the biggest apparent cause of solar failure. When the panels of an array face the sun (and are correctly wired) they produce about 90,000 watts of power.

However, if the station is between the panels and the sun, they produce 0 watts of power. This means that as the panels rotate with auto-tracking, they move through a series of power levels ranging from 90k (full sun) to nothing (station obscures sun). The rotation cycle takes roughly 5 minutes to complete.

Why is this important?

Because of the SMES! See that big white thing in the solar control room? That's the SMES cell. It's a battery used for holding solar energy and transferring it to the station. Click on the SMES and you get a window with input, output, and charging options.

Что нужно знать о SMES'ах

• 1. A battery doesn't charge if the input setting is higher than the actual amount of power being received!
• 2. If the battery charge drops to 0% the battery will stop sending power, even if it is charged again.

A common mistake is to immediately set the input to 90,000 watts (the amount produced by full sunlight) and the output to 80,000 watts. However, this will not work. Solar batteries (SMES cells) start at 20% power but if the engine is off the station drains them to 0% in a few minutes. An input of 90,000 watts (full sun) might charge the battery for a little while, but once the sunlight is blocked by the station the battery charge begins to drain. This causes the battery to turn off and even when the panels receive sunlight again, the battery won't be sending power unless an engineer turns it on again.

Настройка SMES'ов

After you have wired the array, set tracking to auto, and verified that the panels are indeed rotating, set the battery like so:

Charging: Auto

Input: 80,000 watts

Output: OFF!

You want to leave output off and let the battery charge before you send the power to the station. Try waiting for a charge of at least 10% (maybe more) before you turn on the output. The battery needs this charge to provide sustained power during the dark phase of the solar rotation. If the battery runs out of charge, you'll have to turn it on again or it will not provide power. While you wait for the battery to charge, you can wire up other solar arrays on the station.

Alternatively, you don't have to set the output on at all. If the Engine is up and running, you can leave the solar SMES charging just in you need it later.

When you need it, you can set the output to 50,000 - 75,000 depending on how much power you need. If the output load is equal to the output value you set, it means the station needs more power than it's getting. Crank it up!

These four arms can provide enough energy to power the entire ship in the event of a Engine failure. But, given the position to the engine, the wires will likely be eaten away and you will have charging solars that aren't connected to the station.

Внимание!

Есть несколько опасностей подстерегающих вас при настройке солнечных панелей, один из них - поражение электрическим током! Не забывайте одевать изоляционные перчатки во избежании травм или даже смерти.

Скорее всего настраивать панели вы будете в одиночку, поэтому вы уязвимы для предателей или космических карпов. И наконец вы просто можете выпасть в космос, если это случилось, бросьте что нибудь в противоположном направлении для обратного полета.